Question: Can Loose Lug Nuts Cause Noise?

Can wheel nuts work loose?

Wheel nuts are designed not to loosen – unless done intentionally.

I have had my service centre once return the car with one loose wheel nut on each of 2 wheels.

I would think that is utter carelessness by the mechanic working on the car..

What happens if your lug nuts are loose?

If the lug nuts or bolts are loose, the wheel will not be held snugly against the hub of the vehicle. When the vehicle is driven, the wheels will shake. The shaking will be felt in the steering, and likely throughout the whole car.

How long does it take for loose lug nuts to come off?

They could loosen up and fall off one by one over 3,000 miles, but that is a long time. More likely, the lug nuts were overtightened. Tom: Here’s the likely scenario: When you had your stabilizer replaced 3,000 miles ago, someone overtightened your lug nuts.

How much does it cost to tighten lug nuts?

That means you need 80 pounds of force on a 1 foot wrench or 40 pounds on a 2 foot long wrench. Say you have a 2 foot long breaker bar and corresponding socket. That’s what I use for tightening wheel lug nuts. You need to apply 40 pounds of force then.

Do you have to jack up your car to tighten lug nuts?

3 Answers. Nope, doing it with the wheels on the ground if fine, no need to lift the weight of the wheels. It’s easier that way because the wheels can’t turn while you are torquing the lugs.

Why wont my lug nuts stay tight?

The bevel on the lug nuts and on the wheels has to match perfectly for the nuts to stay tight. Usually, if they work loose ONCE, it is enough to compromise the angle on the nuts, the wheel, or both.

How do Lugnuts come loose?

Loose wheel nuts can occur for a variety of reasons, including undertorquing, overtorquing, differential thermal contraction, and improper mating surfaces. Both undertorquing and overtorquing are common when air impact wrenches are used because the actual torque that gets applied depends on so many variables.

How often should lug nuts be replaced?

Lug nuts must be torqued to the manufacturer’s recommended values, and they must be re-torqued to those values after driving approximately 50 to 100 miles on your new tires after the tire service.

What does a loose wheel sound like?

The classic sounds of a bad wheel bearing are cyclic chirping, squealing and/or growling noise. You can also tell that the sound is related to wheel bearings if it changes in proportion to vehicle speed. The sound can get worse with every turn, or it can disappear momentarily.

Is over torquing lug nuts bad?

Over torqued nuts can cause problems too. It stretches the studs reducing the tensile strength which can cause them to snap.

Is it OK to use never seize on lug nuts?

But experts tell us not to use any lubricant, including anti-seize compound, on wheel studs or nuts. The tech folks at Tire Rack state: “Torque specifications are for dry threads only. The fastener threads should be free of oil, dirt, grit, corrosion, etc. It is important NOT to lubricate hardware threads or seats.

Can you tighten lug nuts on the ground?

If you simply want to re-tighten the fasteners, that can be done one at a time on the ground. Step 3: Install the nuts by hand. Install the wheel lugs by hand. … Push the wheel home on the hub and using your socket wrench, tighten the wheel nuts just enough to hold the wheel snugly.

Why does my tire sound loose?

The most common problem with the CV joints is when the protective boot cracks or gets damaged. … When the CV joint becomes damaged or worn, you may hear a clicking, clunking or popping sound coming from this area as the weight of the vehicle puts pressure on this area and shifts back and forth and side to side.

Should you use an impact wrench to tighten lug nuts?

When loosening a lug nut you’ll notice the socket attached to the impact wrench moving slowly as the lug nut is loosened and then quickly when it’s loose. Be cautious when tightening lug nuts using an impact as it’s easy to over torque them—which can stretch or even strip the threads.